|My Image Jacket 1254|
The only wearable garment sewn during this time was a rather simple knit top. I had a RTW cardigan that I had never worn because I did not have a top in the right style and color to wear under it. I wanted a boat neck knit top in a dusty purple color. I had the fabric, but no TNT pattern I could use to make the top. I am always envious of sewing bloggers who make the latest knit top pattern with stunning results and no fit problems. I don’t have that kind of luck. I have fitting problems with knit garments too. I have a bodice sloper for woven fabrics that I can compare to printed patterns. And thought it would be great to have a bodice sloper for knits. But how to get one? There isn’t a lot of info in books or on the Internet, but here is what I found. There appears to be four ways to go about it.
1. Manually draft a bodice sloper for knit fabrics using personal measurements and instructions.
Winifred Aldrich - Metric Pattern Cutting for Women's Wear has instructions for drafting two close fitting blocks, one for very stretchy fabrics (-11 cm wearing ease in circumference) and one for moderate stretch fabric (-4 cm)
Pattern Drafting for Fashion : The Basics by Teresa Gilewska has instruction for a basic knitwear bodice with no ease.
Pattern School a site’s who's main emphasis is stretch-fit pattern making, has instructions for manually drafting a one piece (what I would call a leotard) block that can be used as the basis for a top. On the "Lazy People" tab of this website, there is a screen where you can enter your own measurements and the stretch % of your fabric and it will generate the block for you in .svg file format. Unfortunately you will have to import the svg file into a graphics software to manipulate and save it in a format which can be tiled and printed on 8.5 x 11 paper. I use the freeware PosteRazor to print poster size patterns on 8.5 x 11" paper.
2. Make changes to an existing woven fabric bodice sloper
Sources for instruction on adjusting an existing block for stretch fabrics are
- this post at The Sewing Space In her "free stuff" she has a stretch gauge to use to determine the % stretch of your fabric. The amount of stretch in your knit fabric will determine the amount of ease desired in a pattern for a knit.
- Reportedly, a small section in Patternmaking for Fashion Design by Helen Joseph-Armstrong, which I don’t have in my sewing library so I can't confirm.
- And advice posted on sewing discussion boards:
Advice 1 - “Use close fitting sloper for wovens and increase all seam allowances by 1/8th inch.”
Advice 2 - “Reduce the ease in the circumference of the bodice by folding out a ¼ inch vertical tuck midway on the shoulder all the way down to the hem on the back and front pattern piece. This also reduces the width of the shoulders, but leaves the neck alone. Drop the shoulder just slightly and raise the armscye to make the armhole fit closer to the body. The sleeve width should also be reduced, which can also be done with the same vertical tuck process.
The issue with the advice above is that is does not take into consideration the wearing ease of the block you are using as the basis for the changes, nor the stretch of your knit fabric.
3. Drape a knit fabric, similar in stretchiness to the one to be used for the garment, on a dress form or have a friend do it on you.
The Essential Guide to Stretch Pattern Cutting Shoben Fashion Media available at Center For Pattern Design
Patternmaking-Made-Easy- by Connie Amaden Crawford Who says "A true knit bodice can only be made by draping and smoothing the dart excess out at the shoulder, armhole and side seams."
Both of these sources are a bit pricey.
4. Make a knit top pattern over and over again , adjusting each time for a better fit. This seems to be very popular with younger sewing bloggers, using a popular top pattern from an independent label as their starting point.
Based on my experience, even slopers drafted from my personal measurement require quite a few fitting changes because of my back shape. So just for kicks I decided to drape a knit fabric on my paper tape dress form, which is a good replica of my body (reality sucks!) Initially I used the very brief instructions from Crawford's book. One of my big questions about draping a knit was whether the fabric should be stretched smooth in all directions, which was nearly impossible, or if some wrinkles were permitted. The Shoben pamphlet suggests using a shoulder bust dart initially, so the bust won't be flattened and then transfer it into ease at the side seam as one of final steps. That helped with the wrinkle issue and prevented the dreaded flattened bust (who knew?) . Below are some pictures of my draping exercise. That ring on a string is my improvised plumb bob for determining the vertical seam on the back.
|Draping a knit on dress form - Back|
|Draping a knit on dress form -
Here is what the red knit sloper looked like when compare to woven sloper ( green tag board)
I use the knit sloper and compared it to this Burda pattern 1/20122 123,
narrowed the upper chest and neckline of the pattern , and sewed it up. It fit well and looks great with the cardigan.
Less that 24 hours after taking the pictures above, the back yard looked like this.
I am tired of this highly changeable weather. Have you seen the Internet cartoons about Rudolph the Reindeer helping the Easter Bunny deliver Easter holiday treats to the kids this year? DH and I are heading to Florida in a couple of days as the Spring Break "chaperons" for a group of 18 year old boys. They aren't thrilled about the chaperon bit, but that was a condition of us paying for the condo and other essentials for the trip. They will have plenty of time to "go wild" when their expenses are no longer being charged to my cost center. And I like having an excuse to go somewhere with warmer weather.